lightwalletd/contrib/debian/examples/HUSH3.conf

## HUSH3.conf configuration file. Lines beginning with # are comments.

# Network-related settings:

# Run a regression test network
#regtest=0

# Connect via a SOCKS5 proxy
#proxy=127.0.0.1:9050

# Bind to given address and always listen on it. Use [host]:port notation for IPv6
#bind=<addr>

# Bind to given address and allowlist peers connecting to it. Use [host]:port notation for IPv6
#allowbind=<addr>

##############################################################
##            Quick Primer on addnode vs connect            ##
##  Let's say for instance you use addnode=4.2.2.4          ##
##  addnode will connect you to and tell you about the      ##
##    nodes connected to 4.2.2.4.  In addition it will tell ##
##    the other nodes connected to it that you exist so     ##
##    they can connect to you.                              ##
##  connect will not do the above when you 'connect' to it. ##
##    It will *only* connect you to 4.2.2.4 and no one else.##
##                                                          ##
##  So if you're behind a firewall, or have other problems  ##
##  finding nodes, add some using 'addnode'.                ##
##                                                          ##
##  If you want to stay private, use 'connect' to only      ##
##  connect to "trusted" nodes.                             ##
##                                                          ##
##  If you run multiple nodes on a LAN, there's no need for ##
##  all of them to open lots of connections.  Instead       ##
##  'connect' them all to one node that is port forwarded   ##
##  and has lots of connections.                            ##
##       Thanks goes to [Noodle] on Freenode.               ##
##############################################################

# Use as many addnode= settings as you like to connect to specific peers
#addnode=69.164.218.197
#addnode=10.0.0.2:8233

# Alternatively use as many connect= settings as you like to connect ONLY to specific peers
#connect=69.164.218.197
#connect=10.0.0.1:8233

# Listening mode, enabled by default except when 'connect' is being used
#listen=1

# Maximum number of inbound+outbound connections.
#maxconnections=

#
# JSON-RPC options (for controlling a running hushd process)
#

# server=1 tells node to accept JSON-RPC commands (set as default if not specified)
#server=1

# Bind to given address to listen for JSON-RPC connections. Use [host]:port notation for IPv6.
# This option can be specified multiple times (default: bind to all interfaces)
#rpcbind=<addr>

# You must set rpcuser and rpcpassword to secure the JSON-RPC api
#rpcuser=Ulysses
#rpcpassword=YourSuperGreatPasswordNumber_DO_NOT_USE_THIS_OR_YOU_WILL_GET_ROBBED_385593

# How many seconds node will wait for a complete RPC HTTP request.
# after the HTTP connection is established. 
#rpcclienttimeout=30

# By default, only RPC connections from localhost are allowed.
# Specify as many rpcallowip= settings as you like to allow connections from other hosts,
# either as a single IPv4/IPv6 or with a subnet specification.

# NOTE: opening up the RPC port to hosts outside your local trusted network is NOT RECOMMENDED,
# because the rpcpassword is transmitted over the network unencrypted and also because anyone 
# that can authenticate on the RPC port can steal your keys + take over the account running hushd

#rpcallowip=10.1.1.34/255.255.255.0
#rpcallowip=1.2.3.4/24
#rpcallowip=2001:db8:85a3:0:0:8a2e:370:7334/96

# Listen for RPC connections on this TCP port (default 18031):
#rpcport=18031

# You can use hushd to send commands to hushd
# running on another host using this option:
#rpcconnect=127.0.0.1

# Do not see these options listed in here, but it is in my production lightwalletd config file
#rpcworkqueue=256
#rpcbind=127.0.0.1

# Transaction Fee

# Send transactions as zero-fee transactions if possible (default: 0)
#sendfreetransactions=0

# Create transactions that have enough fees (or priority) so they are likely to # begin confirmation within n blocks (default: 1).
# This setting is overridden by the -paytxfee option.
#txconfirmtarget=n

# Miscellaneous options

# Enable attempt to mine HUSH
#gen=0

# Set the number of threads to be used for mining (-1 = all cores).
#genproclimit=1

# Specify a different Equihash solver (e.g. "tromp") to try to mine
# faster when gen=1.
#equihashsolver=default

# Pre-generate this many public/private key pairs, so wallet backups will be valid for
# both prior transactions and several dozen future transactions.
#keypool=100

# Pay an optional transaction fee every time you send a tx.  Transactions with fees
# are more likely than free transactions to be included in generated blocks, so may
# be validated sooner. This setting does not affect private transactions created with 
# 'z_sendmany'.
#paytxfee=0.00

#Rewind the chain to specific block height. This is useful for creating snapshots at a given block height.
#rewind=777777

#Stop the chain a specific block height. This is useful for creating snapshots at a given block height.
#stopat=1000000

#Set an address to use as change address for all transactions. This value must be set to a 33 byte pubkey. All mined coins will also be sent to this address.
#pubkey=027dc7b5cfb5efca96674b45e9fda18df069d040b9fd9ff32c35df56005e330392

#Forfeit all user rewards to miners. Set this to explicitly not claim user rewards.
#exchange=1

#Donate all user rewards to a a specific address. This value must be set to a 33 byte pubkey.
#donation=027dc7b5cfb5efca96674b45e9fda18df069d040b9fd9ff32c35df56005e330392